Parity Ethereum client is listening to the network for transactions to include in blocks (if mining/validating) or to broadcast. These transactions emitted locally or externally are verified and ordered in a transaction queue. This document aims at describing the process of selecting or rejecting these transactions.
rejected- means that a transaction was not added to the queue.
drop- means that a transaction was added to the queue but got removed later on.
Transactions received from the network must fulfil the following criteria in order to be added to the queue:
--min-gas-price) unless it is a zero gas price transactions aka service transaction allowed by an on-chain managed contract.
gas * gas price) on top of the
max_transaction_sizein the chain specification).
Note that a transaction would be included in the queue if it fulfils the criteria mentioned above and:
current: equals to state nonce + number of already pending transactions. or
future: there is a nonce gap, meaning that the transaction seems to have been received out of order, parity will, therefore, keep it, anticipating that transactions with lower nonces will fill the gap (gap =
transaction nonce). A
futuretransactions will not be propagated nor will it get included in the pending block as it would be invalid.
Once a transaction has been added to the queue, it might get dropped if:
Note that the last 3 conditions require additionally that another transaction with a higher overall score (i.e.
gas price), potentially from a different sender, fulfils the requirement to enter the pool while it’s full.
Given the following transactions in a queue from a same non local sender account:
[TX(nonce=1)| TX(nonce=2) | Tx(nonce=3) | Tx(nonce=4)]
nonce=1 is in the past,
nonce=2 is current,
nonce=4 are in the future.
nonce=1 can be dropped without discussion. The transaction with
nonce=5 would be the “lowest rated” transaction for this sender as it is far in the future. The system would then compare this transaction with the other transactions in the queue from the other senders. The decision to drop a transaction is taken based on the transaction queue strategy (
--tx-queue-strategy), which is
gas_price per default. If the transaction
nonce=5 has the lowest gas price among the “lowest rated” transactions from the queue, it will be dropped.
Local transactions are transactions that have been created or submitted to the local node. Such transactions have a priority boost in the queue - they will get propagated first and included in the pending block first.
Local transactions can be submitted via two RPC methods:
eth_sendRawTransaction. For the former the node has to manage the private key (the sender address), for the latter the transaction is going to be marked as local no matter the sender.
--tx-queue-no-unfamiliar-locals: This flag disables treating all transactions received using
eth_sendRawTransaction as local. Only transactions that are signed by one of the local accounts (private key) will get marked as local, others will be treated in the same way as if they were received over the network.
The flag is recommended in case your RPC is exposed for external (potentially untrusted) clients.
--tx-queue-no-early-reject: Disables early-rejection of the transactions in case the queue is at it’s limits. By default if the pool is full we omit most of the (heavy) verification logic for the transactions and reject transactions early only by looking at their gas price. As a consequence we are not able to identify transactions received from the network as the ones that should be prioritized (local), because the node is managing the private key for them. If that behavior is undesired (i.e. you sign/submit local transactions on node A, then want them to be propagated to node B and prioritized there) you can use the flag to disable early rejection.
The table below shows when transaction is considered as local:
|Received via RPC
||Received via RPC
||Received over the network and sender is local account|
* YES if the pool is not full ** YES if the sender is local account
The RPC API will only show the external transactions that are in the queue. They will never return rejected transactions.
parity_localTransactionswill show up to 25 local transactions, be they already mined, pending or dropped. This RPC method is used in the top section of the Parity UI TxQueueViewer Dapp.
parity_pendingTransactionswill show the transactions added to the queue that will be processed soon (and do not fulfil any of the droping conditions). This RPC method is used in the bottom section of the Parity UI TxQueueViewer Dapp.
parity_allTransactionswill show the transactions added to the queue that will be processed soon as well as the ones that might get dropped.
parity_futureTransactionsis deprecated in favor of
parity_allTransactions. It can be computed by subtracting